Front inner taper roller wheel bearing, for 0.983" dia stub.
Dimensions 52mm o/d x 25mm i/d x 15mm wide.
Dimensions 52mm o/d x 25mm i/d x 15mm wide.
Parts
Front outer taper roller wheel bearing, Fits 8/10hp cars & 100E.
Dimensions 41.3mm o/d x 16mm i/d x 14.7mm wide.
Dimensions 41.3mm o/d x 16mm i/d x 14.7mm wide.
Taper roller inner front wheel bearing assy.
Fits :-
100E & 300E with 1.000" dia stub
Prefect 107E
Anglia 105E & 307E
Cortina Mk 1 1963-66
Fits :-
100E & 300E with 1.000" dia stub
Prefect 107E
Anglia 105E & 307E
Cortina Mk 1 1963-66
Front wheel outer taper roller bearing, 105E-1216-A and 105E-1217-A Fits:- Prefect 107E (eng no 218338 onwards) Anglia 105E Cortina Mk1 up to Nov 1964
Front inner taper roller wheel bearing, fits E83W 10cwt. Dimensions 57mm o/d x 28.5mm i/d x 20mm deep.
Front outer taper roller wheel bearing, fits E83W 10cwt. Dimensions 49mm o/d x 18.9mm i/d x 22mm deep.
Front wheel hub dust cap/grease retainer, 32mm inside diameter 51.5mm outside diameter.
Front hub oil seal, stops grease and oil contaminating the brake shoes. used between 1953-59 with 0.983" stub axle.
Dimensions :- 54mm o/d, 30mm i/d x 7.6mm thick.
Dimensions :- 54mm o/d, 30mm i/d x 7.6mm thick.
Front hub oil seal, stops grease and oil contaminating the brake shoes.
Used on 100E between 1959-62 with 1.00" stub axle. also used on all 105E and Mk1 Cortina 09/62 to 10/64 not GT or Lotus....
Used on 100E between 1959-62 with 1.00" stub axle. also used on all 105E and Mk1 Cortina 09/62 to 10/64 not GT or Lotus....
Front hub oil seal, fits E83W 10cwt and Ford V8 pilot.
Dimensions approx 68.30mm o/d x 37mm i/d x 9.5mm thick.
Dimensions approx 68.30mm o/d x 37mm i/d x 9.5mm thick.
These are original unused but poor stored bearings. They do show very slight signs of corrosion in small places, but are still serviceable as in the words of Bert Thomas 'a little corrosion gives...
Repair sleeves, bearing and seal (axle set) which can be fitted without removing axle from vehicle. over comes the problem of worn bearing surfaces on rear axle casing. this part replaces the...
Repair sleeve, bearing and seal (axle set) which can be fitted without removing axle from vehicle. Overcomes the problem of worn bearing surfaces on axle casing. This part replaces the original...
Rear hub oil seal for all 8/10hp cars with the original wheel bearing fitted.
Not suitable for the Y-1225-RK Rear axle wheel bearing repair kit.
Dimensions 64mm o/d x 36mm i/d x 13mm thick.
Not suitable for the Y-1225-RK Rear axle wheel bearing repair kit.
Dimensions 64mm o/d x 36mm i/d x 13mm thick.
Seal to stop grease contaminating brake shoes 63.5mm o/d, 38mm i/d x 8mm thick
Replacement rear hub oil seal for our wheel bearing repair kits 100E-1225-RK and Y-1225-RK,
Overall dimensions 63.7mm outside, 46.5mm inside, 6.3mm thick.
Overall dimensions 63.7mm outside, 46.5mm inside, 6.3mm thick.
spun steel, 41 mm push fit into drum, preventing grit getting into the bearing
front hub outer bearing snap ring. dimensions 43.25mm outside dia, 35mm inside dia, 2mm thick.
aluminium 4 piece wheel trim for 13" wheels. 4 parts supplied as car set.
Plain top, later style hub cap.
Approx. 238mm overall diameter. inside edge approx 226mm.
Approx. 238mm overall diameter. inside edge approx 226mm.
shouldered wheel stud, fits rear drum only, 7/16 unf thread, overall length 38mm.
Large threaded cap cover to prevent dirt etc entering front wheel bearing. Approx 2 inch diameter.
Retaining spring clip fitted to wheel to hold hub cap onto the road wheel (5 per wheel).
Overall height 37mm with a 5mm fixing hole, width at base 13mm tapering down to 8mm.
Overall height 37mm with a 5mm fixing hole, width at base 13mm tapering down to 8mm.
original refurbished hub cap, finished in grey primer ready for final colour.
Rear hub oil seal for the Ford E83W 10cwt. 81mm o/d x 51mm i/d x 11.3mm thick.
Rear hub gasket, black fibre washer fits under rear hub nut retaining washer, dimensions 25mm o/d, 16mm i/d, 3mm thick.
Front wheel bearing retaining washer, Dimensions 45mm o/d x 19mm i/d x 3.5mm thick with a 4mm key way tongue.
Wheel nut for the 8/10hp cars and 100E models, 7/16"UNF thread, 3/4" A/F hex flats..
Chrome finish hub cap (pattern part).
Approx. 166mm overall diameter. inside edge approx 145mm.
Approx. 166mm overall diameter. inside edge approx 145mm.
Raised dimple top, chrome hub cap . also suit Consul etc. weight approx 400gm.
Approx. 238mm overall diameter. inside edge approx 226mm.
Approx. 238mm overall diameter. inside edge approx 226mm.
inner front wheel bearing spacer, fits 0.983" stub axle.
inner front wheel bearing spacer, fits 1.00" stub axle.
Rear hub grease/oil seal snap ring, 81mm outside diameter, 72mm inside diameter, 4.5mm thick.
Chrome plated hub cap.
Approx. 260mm overall diameter. inside edge approx 227mm.
Approx. 260mm overall diameter. inside edge approx 227mm.
Rubber strip for laying in the well of your wheel before fitting an inner tube, supplied in 17" size only, for smaller size applications the tape can be pulled apart at the joint, trimmed...
Inner tubes for tyres - offset valve for 16" and 18", straight and offset valves available for 17" size.
5.00 x 16"
6.00 x 16"
4.50 x 17"
5.25/5.50 x 18"
5.00 x 16"
6.00 x 16"
4.50 x 17"
5.25/5.50 x 18"
Inner tubes for tyres - offset valve for 16" and 18", straight and offset valves available for 17" size.
5.00 x 16"
6.00 x 16"
4.50 x 17"
5.25/5.50 x 18"
5.00 x 16"
6.00 x 16"
4.50 x 17"
5.25/5.50 x 18"
Inner tubes for tyres - offset valve for 16" and 18", straight and offset valves available for 17" size.
5.00 x 16"
6.00 x 16"
4.50 x 17"
5.25/5.50 x 18"
Marked 175/185R16 -...
5.00 x 16"
6.00 x 16"
4.50 x 17"
5.25/5.50 x 18"
Marked 175/185R16 -...
Inner tubes for tyres - offset valve for 16" and 18", straight and offset valves available for 17" size.
5.00 x 16"
6.00 x 16"
4.50 x 17"
5.25/5.50 x 18"
straight valve, used...
5.00 x 16"
6.00 x 16"
4.50 x 17"
5.25/5.50 x 18"
straight valve, used...
Inner tubes for tyres - offset valve for 16" and 18", straight and offset valves available for 17" size.
5.00 x 16"
6.00 x 16"
4.50 x 17"
5.25/5.50 x 18"
Off-set valve
5.00 x 16"
6.00 x 16"
4.50 x 17"
5.25/5.50 x 18"
Off-set valve
Inner tubes for tyres - offset valve for 16" and 18", straight and offset valves available for 17" size.
5.00 x 16"
6.00 x 16"
4.50 x 17"
5.25/5.50 x 18"
5.00 x 16"
6.00 x 16"
4.50 x 17"
5.25/5.50 x 18"
When balancing wire wheels it is essential for them to be fitted correctly to the wheel balancing machine. If the wheel is mounted using incorrect contact points (i.e. not mounted on its tapered...
When balancing wire wheels it is essential for them to be fitted correctly to the wheel balancing machine. If the wheel is mounted using incorrect contact points (i.e. not mounted on its tapered...
When balancing wire wheels it is essential for them to be fitted correctly to the wheel balancing machine. If the wheel is mounted using incorrect contact points (i.e. not mounted on its tapered...
We stock a selection of vintage pattern tyres, predominantly for the Ford model range we cover. These are usually Excelsior brand (or alternatively Waymaster) which are made off the old Firestone...
We stock a selection of vintage pattern tyres, predominantly for the Ford model range we cover. These are usually Excelsior brand (or alternatively Waymaster) which are made off the old Firestone...
We stock a selection of vintage pattern tyres, predominantly for the Ford model range we cover. These are usually Excelsior brand (or alternatively Waymaster) which are made off the old Firestone...
We stock a selection of vintage pattern tyres, predominantly for the Ford model range we cover. These are usually Excelsior brand (or alternatively Waymaster) which are made off the old Firestone...
We stock a selection of vintage pattern tyres, predominantly for the Ford model range we cover. These are usually Excelsior brand (or alternatively Waymaster) which are made off the old Firestone...
Decorative chrome rim trim for 13" wheels. This item fits against the inner edge of the outer steel wheel rim, being held in place with the integral clips as shown on main picture.
Export of this...
Export of this...
Decorative polished stainless steel rim trim for 14" wheels. This item fits against the inner edge of the outer steel wheel rim, being held in place with the integral clips as shown on the main...
Decorative plain polished stainless steel rim trim for 15" wheels. This item fits against the inner edge of the outer steel wheel rim, being held in place with the integral clips as shown on the...
Decorative plain polished stainless steel rim trim for 16" wheels. This item fits against the inner edge of the outer steel wheel rim, being held in place with the integral clips as shown on the...
Decorative chrome rim trim for 17" wheels. This item fits against the inner edge of the outer steel wheel rim, being held in place with the integral clips as shown on the main picture.
Export of...
Export of...
Stainless steel domed wheel nut for the Model Y, 7/16"UNF thread, 3/4" A/F hex flats, overall length 1".
front hub grease cap 1932 to 1955 , threaded base and hexagonal top.
Front wheel bearing retaining washer, Dimensions, 32mm o/d x 16mm i/d x 2.5mm thick with a 3mm key way tag.
Prices shown include VAT @ 20% where applicable
